CoroMill® MR80
Kostenefficiënt vlakfrezen en profielfrezen
Assortiment, freeslichamen
| Freeslichaam | Ø | Vertanding | zn | Koppelingstype | Onderlegplaat | Inwendige koeling |
| Inch | 2" | M, H – even | 4, 6 | Doornbevestiging TDA ¾" | Ja | Ja |
| Inch | 2 ½", 3", 4" | M – even | 6–10 | Doornbevestiging TDA ¾" & 1" Arbor TDB 1 ½" | Ja | Ja |
| Metrisch | 32 mm | H – even | 3 | Cilindrisch 32 | Nee | Ja |
| Metrisch | 40 mm | H – even | 4 | Cilindrisch 32 | Ja | Ja |
| Metrisch | 50–100 mm | H – even | 4–10 | Doorn TDA 22–32 | Ja | Ja |
| Metrisch | 50–100 mm | H – even | 6–12 | Doorn TDA 22–32 | Ja | Ja |
Assortiment, wisselplaten
| Wisselplaatgrootte | Wisselplaatgeometrie | Hardmetaalsoort |
| 12 | E-L50 | GC1040, GC1130, GC4330, GC4340, S30T |
RMPX, AZ, GAMF en GAMP
| Freeslichaam Ø | Infreeshoek RMPX | Max. plunge diepte AZ, mm (inch) | Radiale helling GAMF | Axiale helling GAMP |
| 32 mm (H) | 0,86° | 0.15 (0.006) | -19° | -7° |
| 40 mm (H) | 0,86° | 0.27 (0.011) | -15° | -7° |
| 50 mm (M / H) | 0,74° | 0.36 (0.014) | -12° / -14° | -7° |
| 63 mm (M / H) | 0,59° | 0.42 (0.017) | -12° / -14° | -7° |
| 80 mm (M / H) | 0.43º | 0.44 (0.017) | -14° / -12° | -7° |
| 100 mm (M / H) | 0,33° | 0.44 (0.017) | -14° / -12° | -7° |
| 2 inch (M / H) | 0,74° | 0.36 (0.014) | -12° / -14° | -7° |
| 2 ½ inch (M) | 0,59° | 0.42 (0.017) | -12° | -7° |
| 3 inch (M) | 0.43º | 0.44 (0.017) | -14° | -7° |
| 4 inch (M) | 0,33° | 0.44 (0.017) | -14° | -7° |
Snijgegevens, hex aanbevelingen
| ISO-gebied | Referentiemateriaal | Wisselplaatgeometrie | hex aanbeveling, mm (inch) | fz aanbeveling, mm (inch) |
| ISO P | MC: P2.1.Z.AN | E-L50 | 0.1 (0.08–0.15) 0.004 (0.003–0.006) | 0.12 (0.09–0.17) 0.005 (0.004–0.007) |
| ISO M | MC: M1.0.Z.AQ | E-L50 | 0.1 (0.08–0.15) 0.004 (0.003–0.006) | 0.12 (0.09–0.17) 0.005 (0.004–0.007) |
| ISO K | MC: K2.2.C.UT | E-L50 | 0.1 (0.08–0.15) 0.004 (0.003–0.006) | 0.12 (0.09–0.17) 0.005 (0.004–0.007) |
OPMERKING: fz wordt berekend met ap = 3 mm (0.118 inch) en ae = 75% DCX
Snijgegevens, vc aanbevelingen
| ISO-gebied | Referentiemateriaal | Hardmetaalsoort | vc aanbeveling, m/min (ft/min) |
| ISO P | MC: P2.1.Z.AN | GC1130 | 240 (215–250) 787 (705–820) |
| MC: P2.1.Z.AN | GC4330 | 280 (255–295) 919 (837–968) | |
| MC: P2.1.Z.AN | GC4340 | 240 (215–250) 787 (705–820) | |
| ISO M | MC: M1.0.Z.AQ | GC1040 | 155 (135–165) 509 (443–541) |
| MC: M1.0.Z.AQ | GC1130 | 225 (200–235) 738 (656–771) | |
| MC: M1.0.Z.AQ | GC4340 | 185 (165–195) 607 (541–640) | |
| MC: M1.0.Z.AQ | S30T | 215 (185–230) 705 (607–755) | |
| ISO K | MC: K2.2.C.UT | GC4330 | 185 (170–195) 607 (558–640) |
OPMERKING: vc wordt berekend met ap = 3 mm (0.118 inch) en ae = 75% DCX
Doe met ons mee. Blijf op de hoogte.
Registreer u vandaag nog voor onze nieuwsbrief
Sandvik Benelux B.V. - Division Coromant
+31108080280